Losmandy GM8 User Manual

Getting Started

Depending on which accessories you ordered, your GM-8 mount was shipped in two to four boxes. The contents of each box are as follows:
  • Equatorial Mount
  • Adjustable Tripod, Counterweight Shaft
  • Digital Drive Box, Hand Control, Cables, Mounting Bolts, Allen Wrench, Counterweight Safety Screw
  • 7 lb. Weight, Locking Bolt
Remove all the parts from their respective boxes and place them on a flat, clear work area. A large floor space is ideal. When setting up your Losmandy G-M8, you must start with the tripod and work from there. To insure proper assembly, each task must be performed in the specific order as defined by these instructions.

Exploded diagram of parts of Losmandy G11 Mount

Assembling the tripod

The tripod comes pre-assembled. Place the Digital Drive Unit into the brackets on the tripod and lock in place with the supplied knobs.

Attaching the equatorial mount

After the tripod is set up, you are ready to attach the equatorial mount. This is the platform to which the telescope attaches and allows you to direct it anywhere in the sky. The mount is also adjustable so you can orient the axis of rotation to make it parallel with the Earth’s axis of rotation (see the section on Polar Alignment). To attach the equatorial mount to the tripod:
  1. Insert the base of the equatorial mount into the top of the central column.
  2. Rotate the equatorial mount on the central column until the holes in the mount line up with those in the central column.
  3. Insert the three screws provided through the holes in the central column and into the equatorial mount.
  4. Tighten the screws to hold the equatorial mount in place.
There are three possible orientations of the equatorial mount which allow you to select the most convenient location of the electronic console.

Attaching the counterweight bar

To properly balance the telescope, the mount comes with a counterweight bar and counterweight. To install the counterweight bar:
  1. Locate the opening in the equatorial mount on the DEC axis. It is opposite the telescope mounting platform
  2. Thread the counterweight bar into the opening until tight.
Once the bar is securely in place you are ready to attach the counterweight(s).

Attaching the counterweight

The Losmandy GM-8 comes standard with one 7 lb. counterweight. To install the counterweight:
  1. Orient the mount so that the counterweight bar points toward the ground.
  2. Remove the counterweight safety thumbscrew and washer on the end of the counterweight bar (opposite the end that attaches to the mount).
  3. Loosen the locking bolt on the side of the counterweight.
  4. Slide the counterweight onto the shaft.
  5. Tighten the locking bolt on the side of the weight to hold it in place.
  6. Repeat this process if using a second optional counterweight.
  7. Replace the counterweight safety thumbscrew and washer.

Attaching the telescope to the mount

The telescope attaches to the mount via a dovetail bar bolted to the bottom of the telescope. Before you attach the optical tube, make sure that the declination and right ascension clutch knobs are tight. This will ensure that the mount does not move suddenly while attaching the telescope. To mount the telescope tube:
  1. Loosen the knob on the side of the telescope mounting platform. This allows you to slide the dovetail bracket of the telescope onto the mount.
  2. Slide the dovetail bar of the telescope tube into the mounting platform of the mount. Slide the telescope so that the back of the dovetail bar is almost flush with the back of the mounting platform.
  3. Tighten the knob on the side of the mounting platform to hold the telescope in place.

Installing the polar alignment finder

To aid in polar aligning the mount, your Losmandy GM-8 accepts an optional Polar Axis Finder which fits directly into the polar axis. To install:
  1. Remove the polar axis end covers by rotating counterclockwise.
  2. Insert the objective end of the Polar Axis Finder into the opening on the lower end of the polar axis.
  3. Rotate the slip ring on the Polar Axis Finder until snug. The Polar Axis Finder should still rotate without play.

Installing the polar alignment illuminator

If you look through the Polar Axis Finder in the daytime the reticle is clearly visible. To see the reticle at night, however, you need to install the illuminator.
  1. Remove the plastic battery holder from the battery pouch.
  2. Insert two AA batteries into the plastic battery holder.
  3. Attach the cable with the 9-volt style terminal to the battery holder.
  4. Place the battery holder back into the battery pouch.
  5. Thread the LED illuminator into the hole on the side of the polar axis finder.
  6. Insert the connector on the wire which attaches to the LED into the wire connector from the battery housing. The LED will illuminate.
The Polar Axis Finder is now installed and ready to use. To turn the LED off, unplug the wires that connect the LED to the battery housing.

Moving the telescope in R.A. and DEC

Once the telescope is set up, you will need to point it at various locations to observe different objects. Unlike other systems, the Losmandy mounts have a clutch system. To make rough adjustments, loosen the R.A. and DEC clutch knobs slightly and move the telescope in the desired direction. The R.A. clutch knob is near the Polar Axis Finder while the DEC clutch knob is at the top of the counterweight bar. How tight should the clutch knobs be? You set the clutch knobs to the friction you like. When you want to move the telescope, all you do is grab the telescope and move it to its new position.

For fine adjustments, use the fast-set function on the hand control box. For more information please see the section on Using the Drive.

Balancing the telescope on R.A.

To eliminate undue stress on the mount, the telescope should be properly balanced around the polar axis. Proper balancing is crucial for accurate tracking. To balance the mount:
  1. Verify that the telescope securing knob on the telescope mounting platform is tight.
  2. Loosen the R.A. clutch knob and position the telescope off to one side of the mount. The counterweight bar will extend horizontally on the opposite side of the mount.
  3. Release the telescope to see which way the telescope may drift as a result of an imbalance.
  4. Loosen the locking bolt on the side of the counterweight so it can slide along the length of the counterweight bar.
  5. Move the counterweight to a point where it balances the telescope. The telescope should remain stationary when the R.A clutch knob is loose.
  6. Tighten the locking bolt on the counterweight to hold it in place.
While the above instructions describe a perfect balance arrangement, there should be slight imbalance to ensure the best possible tracking. When the scope is on the west side of the mount the counterweight should be slightly imbalanced to the counterweight bar side. And when the tube is on the east side of the mount there should be a slight imbalance toward the telescope side. This is done so that the worm gear is pushing against the slight load. THE AMOUNT OF THE IMBALANCE IS VERY SLIGHT. When taking astro-photographs, this balance process can be done for the specific aim of the telescope to further optimise tracking accuracy.

Balancing the mount in DEC

Although the telescope does not track in declination, the telescope should also be balanced in this axis to prevent any sudden motions when the DEC clutch knob is loose. To balance the telescope in DEC:
  1. Loosen the R.A. clutch knob and rotate the telescope so that it is on one side of the mount (as described in the previous section on Balancing the Mount in R.A.).
  2. Tighten the R.A. clutch knob to hold the telescope in place.
  3. Loosen the DEC clutch knob and rotate the telescope until the tube is parallel to the ground.
  4. Release the tube to see which way it rotates around the declination axis.
    DO NOT LET GO OF THE TELESCOPE TUBE COMPLETELY!
  5. Slightly loosen the knob that holds the telescope to the mounting platform and slide the telescope either forward or backward until it remains stationary when the DEC clutch is loose.
    DO NOT LET GO OF THE TELESCOPE TUBE WHILE THE KNOB ON THE MOUNTING PLATFORM IS LOOSE.
  6. Tighten the knob on the telescope mounting platform to hold the telescope in place.

Like R.A. balance, these are general balance instructions and will reduce undue stress on the mount. When taking astro-photographs, this balance process should be done for the specific area at which the telescope is pointing.

Adjusting the mount for polar alignment

In order for the clock drive to track accurately, the telescope’s axis of rotation must be parallel to the Earth’s axis of rotation, a process known as polar alignment. Polar alignment is achieved NOT by moving the telescope in R.A, or DEC, but by adjusting the mount vertically, which is called altitude, and horizontally, which is called azimuth. This section simply covers the correct movement of the telescope during the polar alignment process. The actual process of polar alignment, (making the telescope’s axis of rotation parallel to the Earth’s) is described later in this manual in the section on Polar Alignment. To adjust the mount in altitude:
  1. Locate the altitude adjustment knob - directly below the counterweight shaft.
  2. Turn the altitude adjustment knob until the mount is at the right elevation. Each complete revolution of the knob raises or lowers the polar axis 3.2°.
The altitude range is from 14° to 64°. If you live at latitudes closer to the poles, you will need the Zero Degree Latitude Adapter which is sold as an optional accessory and increases the latitude range from 0° to 84°. To adjust the mount in azimuth:
  1. Locate the azimuth lock screws and adjustment knobs on the back of the mount.
  2. Loosen the two azimuth lock screws on each side of the mount.
  3. Turn either of the azimuth adjustment knobs until the polar axis is pointing in the right direction. Each complete revolution of the knob is .82°.
  4. Tighten the azimuth lock screws to hold the mount in place.
The mount can be moved ± 8.5° in azimuth using these knobs.

Keep in mind that adjusting the mount is done during the polar alignment process only. Once polar aligned, the mount must NOT be moved. Pointing the telescope is done by moving the mount in right ascension and declination, as described earlier in this manual. Once the appropriate adjustments have been made and you are aligned on the celestial pole, turn the clock drive on and the telescope will track.
 


 
 

GM8 Technical Specifications

Below is pertinent technical information on your Losmandy GM-8 telescope that technophiles may find useful.
R.A. & DEC axis
  • All machined construction
  • One 2.10" thrust bearing
  • One 2.00" thrust bearing
  • Two 1.50" needle bearings
  • 2.8" diameter 7075 aluminium gear with l80 Teeth
  • Dual supported ball bearing housed stainless steel worm, heated treated and ground
  • 1.25" diameter centerless ground aluminium shafts
  • Tangent arm design altitude adjusts 0°- 64°
  • Latitude scale in 2° increments
  • Single knob control azimuth, bi-directional ±8.5°
  • 3.5" diameter laser engraved setting circles, 6 minutes R.A, 2° DEC
  • 160 oz/in stepper driven
  • Dovetail saddle plate-allowing for interchanging of any tube assembly
  • Removable counterweight shaft with safety knob
  • 7 lb. counterweight included
  • 7 lb., 12 lb. and 21 lb. extra counterweights available
  • Through the axis polar alignment finder (northern and southern hemisphere) available as an option
  • Instrument weight capacity 40 pounds
  • Equatorial head less tripod and motors, 17 pounds
Tripod
  • All machined
  • Tripod height, adjustable (24 - 42 inches)
  • Fold up tripod design for ease of transport
  • Tripod weight 15 lbs.
Dual-axis electronics
  • Diamond push button pattern
  • R.A. and DEC Reversing Switches
  • Three Photo Guide Rates ± 30 %, 50% and 2x sidereal rate
  • Four Setting Rates: 4x, 8x, 16x sidereal rate, and 32x (HST)
  • Quartz Tracking Rates; sidereal, solar, lunar, King
  • Periodic Error Correction (PEC)
  • Control Panel Dimmer
  • Accepts Auto-Guider Systems
  • Northern and Southern Hemisphere operation
  • TVC - Programmable DEC Backlash Compensation
  • 12 Volt DC - 500 mA power use
  • Tilt-able Control Panel for easy access
  • Small Hand Control box for comfortable use
Distance from the top of the tripod to the DEC/R.A. junction (at 34°) is 9".
Distance from the DEC/R.A. junction to the top of the saddle is 6".

Please note that these specifications are subject to change without notice and stated for the Losmandy GM-8 mount with the standard accessories.
The GM-8 drive system
The drive system uses a 2.800" diameter 7075 aluminium gear with 180 teeth for incredibly accurate tracking. One of the most unique features of the new drive is the Periodic Error Correction (PEC) function. This feature allows the drive system to learn the characteristics of the worm gear, and as a result, improve the tracking accuracy even more. This typically reduces the periodic error to 30 percent or less of the original error. The amount of improvement varies depending on guiding skill, atmospheric stability, the characteristics of the worm gear, and the accuracy of polar alignment. Following is a brief discussion of each feature.
Power Up the Drive
In order to activate the drive, you must first plug it into an external power source. To supply power to your Losmandy G-11 plug your DC or AC power cord into the outlet on the electronic console labeled "12V IN." Then, plug the other end of the adapter into the appropriate power source (either AC or DC depending on the adapter used).

Next, plug the R.A. and DEC cables into the electronic box. The receptacles are on the upper right portion of the box (R.A. is on the left; DEC is on the right). Then plug the cables into the respective motors.

Once plugged into the proper power source, activate the drive by placing the ON/OFF switch in the "ON" position. Once activated, the drive begins tracking at the default sidereal rate. The LED below the sidereal rate icon will illuminate.
G/S (Guide Setting)
This function allows you to select the speed at which the motor moves when corrections are made via the hand controller. Once the drive is activated, the default setting is .3 times sidereal rate. Press the button to change the guiding rate. The sections are .3x, .5x, 2x, 4x, 8x, and 16x sidereal rate.

For guiding, use either the .3x or .5x setting. These two rates allow optical use with auto guiders. For auto guiders, use the 2x setting for calibrating and .5x for playback. The faster settings of 2x, 4x, 8x, and 16x are perfect for positioning objects within the field of view.

To move the telescope at the 16x speed WITHOUT changing the guide setting, press the button that corresponds to the direction you want to move the telescope. While holding the button down, press the opposite directional button. For example, if you want to move the telescope west, hold the west button down and then press the east button. Conversely, if you want to move the telescopes east, hold the east button down and then press the west button. This fast-set function also works in declination.

NOTE: THE R.A. SETTING CIRCLE DOES NOT REMAIN CALIBRATED WHEN USING ANY OF THE SLEWING RATES.
TVC - Time Variable (Dec. Backlash) Compensation
The TVC (Time Variable Compensation) function allows you to eliminate the backlash in the DEC motor when changing directions such as from north to south or vice versa. Each time you change the direction of the telescope in declination, the motor speeds up momentarily to take up any slack, There are ten settings - each indicated by an illuminated red bar. The best setting is determined by looking through the eyepiece while changing the direction of the DEC motor and then moving through the TVC settings until the backlash has been eliminated.

To activate this function, press the TVC button. Once activated, the bar on the far right of the display will illuminate. Press the TVC button again, and the next bar will illuminate, and so on for all ten settings. Note that the first bar (on the far right) always stays illuminated while the TVC function is activated. A setting of three to six bars typically eliminates any backlash. The TVC must be reset each time you power up the drive.
Tracking Rate Selection
The drive has four basic rates: sidereal, King (a modified sidereal rate), solar, and lunar. While solar and lunar rates are obvious, sidereal and King rates require a little more explaining. Sidereal rate is based on a single rotation of the Earth which takes 1,432.5 minutes. Unfortunately, atmospheric refraction causes objects near the horizon to move at slightly different rates, a fact discovered by an astronomer by the name of King. The King Rate takes into account this refraction caused by the Earth’s atmosphere and is recommended for deep sky astro-photography. For deep-sky observing, either King or sidereal rate is fine.

Each of the tracking rates is represented by an icon. Sidereal rate is represented by a star, King rate by a crown, solar rate by a sun, and lunar rate by a crescent moon. Underneath each icon is an LED to indicate which rate has been selected. Once the power has been turned on, the drive tracks at the default sidereal rate. To change the tracking rate, press the "RATE" button. Pressing the button increments the rates sequentially from left to right as listed previously.

NOTE: The PEC does NOT have to be activated for the drive to work. Once PEC is activated, however, you can only use .3x or .5x tracking rate. You can not change to a faster rate until PEC is turned off.
Periodic Error Correction (PEC)
Periodic Error Correction, or PEC, is a system that improves the tracking accuracy of the drive. PEC is designed to improve photographic quality by reducing the amplitude of the worm gear errors. Periodic error is a slight oscillation in right ascension caused by imperfections in all drive gears. The cycle of the periodic error is equal to one rotation of the worm gear, which is four minutes for the G-11. No matter how precise, all telescope drives will have some periodic error, though it is already extremely low on the Losmandy G-11. Using the PEC function is a two-step process. First, you must guide for at least four minutes, keeping the guide star centered on the cross hairs of your guiding eyepiece, during which time the system records the correction you make. It takes the worm gear four minutes to make one complete revolution, hence the need to guide for four minutes. The second step is to play back the corrections you made during the recording phase. The microcomputer inside the electronic console does this automatically after one revolution of the worm gear. Keep in mind that this feature is for advanced astro-photographers and requires careful guiding. Here’s how to use the PEC function most effectively.
  1. Find a bright star relatively close to the object you want to photograph.
  2. Insert a high power eyepiece with illuminated cross hairs into your telescope. Orient the guiding eyepiece cross hairs so that one is parallel to the declination axis while the other is parallel to the R.A. axis.
  3. Cent er the guide star on the illuminated cross hairs, focus the telescope, and study the periodic movement.
  4. Take a few minutes to practice guiding. This will help you familiarize yourself with the periodic error of the drive and the operation of the hand control box.
  5. Press the "PEC" button once to activate the mode. The LED will flash once a second for five seconds before it begins recording your hand corrections. The .3x guiding rate is optimum for this function. For best results, the star should be centered on the cross hairs for a few seconds before activating the PEC function.
  6. Guide for four minutes. Try not to overshoot corrections in right ascension. Ignore drift in declination. During the record phase, the LED flashes a little faster.
After eight minutes, the system begins to play back the corrections made during the first four minutes. When playing back, the LED stays on without blinking. The fast-set function is locked while PEC is activated. This eliminates the possibility of moving the telescope during the exposure.

Once you have used the PEC function for a while you may mistake its operation for the way the drive normally operates. The best way to see how well the PEC function works is to turn if off and note the change in tracking. PEC results improve with practice and patience.
Dim
The DIM button changes the intensity of the LED displays. There are five brightness ranges with the default to the maximum setting. This feature allows the LEDs to be dimmed to an acceptable level so as not to be a distraction when observing and photographing
HC/CCD
This modular phone style outlet accepts the hand controller needed for guiding and moving the telescope. In addition, the outlet is wired to accept all SBIG Auto Guiders. Push the connector on the cable into the outlet until the plastic tab clicks. To remove the cable, squeeze the plastic tab and pull away from the outlet. Phone jack splitters are available so that the hand controller and auto guider can be used at the same time.
12 VDC in
This outlet is used to supply power to the telescope mount. Your Losmandy G-11 comes standard with a DC adapter. To install, plug the connector into the electronic box first, then the power source.
12 VDC out
The 12 V DC OUT is for auxiliary accessories that require power, such as digital setting circles. The accessories need a plug like the one on the DC adapter. NOTE: Cent er core positive(+) plug.
R.A./DEC outlets
In the upper right corner of the electronic console are two modular phone-type outlets; one labeled R.A. for the Right Ascension motor, and the other DEC for the Declination motor. Push the connector at the end of the cable into the outlet until the plastic tab clicks. To remove the cable, squeeze the plastic tab and remove it from the outlet.
Northern/Southern hemisphere operation
When using your Losmandy GM-8 in the southern hemisphere, there is a need to reverse the motors. In some mounts this is accomplished by installing a reversed motor. In the GM-8 the direction the drive motor moves the telescope is within the control of the user. Changing from northern hemisphere to southern hemisphere requires changing the polarity of the drive motor. To do this:
  1. Remove the cover of the electronic box by removing the four screws (one in each corner).
  2. Locate the north/south switch (labeled N/S) just to the right of the ON/OFF switch.
  3. Change the switch from "N" to "S" setting. NOTE: If the "N" or "S" is not visible, the N position is away from the edge of the circuit board; S is toward the edge.
  4. Replace the cover.
The direction of the drive motor is now reversed and will work in the southern hemisphere. Changing from the southern hemisphere to the northern hemisphere requires flipping the switch from the "S" to "N" setting.

For quick changes, press one of the R.A. buttons while powering up the drive. Which R.A. button do you press? It depends on the directional setting of the R.A. switch (see the section on R.A./DEC REVERSE). The best way is to do it by trial and error; press one button while powering up the drive. If it does not work, turn the drive off and try the process again while pressing the other R.A. button.

The hand controller allows you to move the telescope in R.A. and DEC using the corresponding motors. This includes fine corrections for guided astro-photography and minor adjustments for centering objects in the field of view. The buttons on the hand controller are intentionally labeled rather simply. This is due to the fact that the direction of motion of the mount varies depending on how the telescope is oriented. Furthermore, these buttons are user definable to eliminate confusion when guiding. For more information, see the section on R.A./DEC Reverse.

Once again, to move the telescope at the 16x speed WITHOUT changing the guide setting, press the button that corresponds to the direction you want to move the telescope. While holding the button down, press the opposite directional button. For example, if you want to move the telescope west, hold the west button down and then press the east button. Conversely, if you want to move the telescope east, hold the east button down then press the west button. This fast-set function also works in declination.
R.A./DEC Reverse
As mentioned previously, the direction a particular button moves the mount varies depending on the telescope’s orientation (i.e., whether its on the east or west side of the mount.) This can create confusion when guiding if you change the telescope’s orientation during a given photographic session. To compensate for this, the direction of the R.A. and DEC buttons are changeable. To reverse the direction of either the R.A. and/or DEC buttons change the switch setting of the appropriate axis. The switches that control these settings are found on the upper portion of the hand controller.

The next section deals with observational astronomy in general. It includes information on the night sky, polar alignment, and using your telescope for astronomical observing.

And finally, if you're having problems, then check out the troubleshooting guide


losmandy.co.uk is brought to you by Venturescope your friendly Telescope retailer in the UK.             Sitemap